1999 INTERNATIONAL 4900

1999 international 4x2 slick line unit for sale , includes : tools and line all in good turnkey shape to go to work , motor was redone in 2016 and less then approx 6000 km put on truck since 20000ft of stainless steel line was purchased , approx 18000 steel .108 line

wireline van and wireline tools. All tools on list are good as new conditions with some new running/pulling tools.

2.            Wireline truck is 2000 IHC 288,160 km, new motor 2016, approximately 6,000 km on new motor.

3.            Wireline van built by Intercontinental Van Body in 2000. Aluminum body, no rust.

4.            Draw-works: built in Calgary

6.            Preference to sell Wireline Unit with Tools.

Dual drum - 20,000 FT/drum 0.108 Line 20,000 FT new stainless line in 2016

Wireline Unit

Fully tooled single axle wireline unit

Comes with a .108” Stainless steel line

Sour Service 35Mpa (5000 psi) lubricator and BOP’s.

Capable of any fishing, plug, sleeve & plunger lift systems to 4000m

Electronic pressure recorders for gradients, flows and buildups. 

Main Tool Cabinet:

2" X running tool

2 ½" X running tool

2" inside wire grab

2 ½" inside wire grab

2" J unlatching tool

2 ½" J unlatching tool

1.85" swaging tool

2" tubing end locator

¾" JUC overshot

1" JUC overshot

1.25" JUC overshot

2" wax knife (wireline style)

2" tubing/nipple brush

2" /2 ½" ring style wax knife/gauge ring

2 ½" Otis shifting tool

2" Otis shifting tool

1.75" Otis shifting tool

1.25 GS pulling tool

2" GS pulling tool

2 ½" GS pulling tool

1.25" gauge ring

1.75" gauge ring

1.75" swab mandrel (2)

1.5" swab mandrel

2 ½" SB overshot

2 ½" JDC overshot

1.75" impression block (2)

2" baker plug running tool (2)w/ rings

2" SB overshot

2" Bowen positive grab overshot

. 75" ropesocket

Vise Cabinet:

Assorted steel brass and aluminum shear pin Assorted punches and open end wrenches 1.5" threaded stem subs (3)

Pliers, vise grips, wireline cutters

Wireline clamp (1)

Lubricator and Toolstring:

5' x 1.5" sinker bar (3) w 5/8" pin and box

3' x 1.5" sinker bar (1) w 5/8" pin and box 1.5" spang jars (2) 1 short stroke, 1 long stroke Lee hydraulic jars (1) 1.5"

5 x 1.25" sinker bar (2)

1.25" spang jar (1)

Hydrostatic bailer 1.62" x 5' w 1.62" shoe (2) 1.62" x 3' bailer extension sub

2 7/8" x 10' lubricator w/ Bowen unions (2)

Swage/BOP compartment:

2" LP Bowen union swage

2 3/8" EUE Bowen union swage

2 7/8" Bowen union swage

1.906" long gauge ring

Equalizing shear prong

3" Bowen flow sub (2" and ½" ports)

3" Bowen stuffing box

4” x 3” bowen swage

1.5" drop cutter bar

Operating Compartment:

2 Baker FSG plug complete

2” Otis PX plug complete

2” broaching tool (new)

2” CW hookwall plug (no element)

2” RB overshot skirt

2” outside wireline grab

.75” JUC overshot

Type A positive grab fishing tool 2" Baker shifting tool collet

2 ½" Baker shifting tool collet

2” baker choke sub

0.5'' Otis RB overshot

0.5'' J unlatching tool

1 3/16” JDC skirt and core spring

2 ½” Bowen positive grabe outer sleeve

2” and 2 1/2 “ Otis overshot skirts (3)

2” A Probe

2 ½” A probe

2" B probe

2 ½” B probe

Assorted ¼11 and ½11 pressure gauges

2 0 ring kits (partially full)

Hookwall plug latch assemblies (2)

2” G packoff plug parts (2 complete plugs)

2 ½ “ G packoff plug parts (1.5 plugs)

2.343” long gauge ring

2 7 /8" positive grab sub

2" Baker G bottoms (3)

2 ½" Baker G bottom (2)

Assorted Baker 2" and 2 ½" plug latch assemblies (18) Baker plug prongs (7)

Assorted F stops (6)

Recorder holdowns (4)

Holdown dogs 2" and 2 ½"

Baker plug parts - assorted

1 3/16" J heads (4)

2" Baker shifting tool

2 ½" Baker shifting tool

2" CB hookwall plug (toolbox)

2" x 2 ½" mechanical perforator (red toolbox)

From Picker Deck:

8' x 2 7 /8" lubricator w/Bowen unions (6)

6' x 2 7 /8" lubricator w/Bowen unions (2)

4' x 2 7 /8" lubricator w/Bowen unions (1)

6' x 23/8" lubricator w/Bowen unions (4)

4" pup joint w/3" taper w/Bowen unions

Shop Bench:

2" JDC overshots (2)

2" Z Baker Z locks (2)

2 3/8" pup joints w/Bowen unions

More Info

1- 3.66" SB overshot w/3/4" pin

1-3" GS pulling tool

1- 3.66" SB skirt w/ 4 dogs

1- 2.87" impression block

1- 3.66" bell threaded to 2" JDC skirt

1- 1.75" magnet w/ 5/8" pin

1- 2.8" JDC overshot w/ 5/8" pin

1- 2.33" Bowen positive grab overshot w/ 5/8" pin

1-      2.25" impression block

3" Otis dog release tool

2-            rig brushes

2- pails varsol

2- spray cans red paint

1- 3"/4" cored pulling tool

1 sleeve Teflon tape

1- 2" hydrostatic bailer

1- 1 1/2" long stroke hydraulic Jars